GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual
GuangZhou Walkera Technology Co., Ltd 2.4GHz Transmitter DEVO 12E manual
Contents
- 1. Users Manual part 1 of 11
- 2. Users Manual part 2 of 11
- 3. Users Manual part 3 of 11
- 4. Users Manual part 4 of 11
- 5. Users Manual part 5 of 11
- 6. Users Manual part 6 of 11
- 7. Users Manual part 7 of 11
- 8. Users Manual part 8 of 11
- 9. Users Manual part 9 of 11
- 10. Users Manual part 10 of 11
- 11. Users Manual part 11 of 11
Users Manual part 9 of 11
oieUeniion Welcome to use the DEVO 12E transmitter DEVD 1 EE 2.1 Model Select Press ENT to enter Main Menu and press UP or DN to make Model Model Select Ellll Menu is selected. Press ENT to get the Model Menu and press UP or DN to select Model select, press ENT to enter the Model Select —| setting interface. 2 ._§ Model 2 Press UP or DN to select the model you desired, press ENT to confirm 3 '-§ Model 3 and marks'R/‘in the front ofselected one. Total 30 models are optional. 4 ._§ Model 4 Press EXT to exit after finished. 2.2 Model Name In the menu of model name, you can make a desired name for your model for long term storage. Its data can be directly withdrawn in next flightsRepeat the step “2.1 Model Select" to choose the model you want to name or save, press EXT to back to the interface. Press “ENT" to enter Main Menu. press UP or DN to select “MODEL Model Name Eliii Menu“, then Press “ENT" to enter Model Menu; Press UP or DN to select "Model NAME" and then press “ENT" button to enter the "Model No. 1 Name" setting interface. N ame Press UP or DN to select the character and figure which are needed to be changed, press R or L button to change the character and figure, mo d e | 1 and press UP or DN to set next one. Press EXT to exit after finished. 2.3 Model Copy Press ENT to enter "Main Menu" and press UP or UN to make "Model Menu" is selected. Press ENT to enter "Model Menu" and press UF' or DN to select" Model Copy", press ENT to the "Model Copy" setting interface. Model Copy Press UP or DN to choose the I model you want to be copied Model Copy iiii Source I Source: 1 Model 1 as source model and press «1 N Model 1 0551 ENT to confirm, The serial No. ¢1 N Model 1 and model name of Source 2 h? Model 2 Model Will be shown as left 3 he Model 3 2 "§ M°d°' 2 Illustration. Model Copy Then press UP or DN to locate the source model, press ENT to confirm. Then an enquire “Are you sure?" is popped up as below Illustration. Press ENT to copy, or press EXT to exit. Source: 1Model 1 Best: 2 Model 2 Are you sure? 2.4 Model wireless copy The model data between two DEVO 12E equipments can be Wirelessly copied via Model Transmit and Model Receive in Model Menu. (1) Model transmission Press ENT to enter "Main Menu" and press UP or DN to select "Model Menu". Press ENT to get ”Model Menu" and press UP or DN to select "Model transmission", continue to press ENT to enter "Model Transmit" setting interface. Model Transmit llll Model Transmit Press UP or DN to choose the .. v .. . . Source model which will be No. 1 transmitted, and press ENT to Model 1 confirm. an enquiry information “Are you sure?" will be shown as left Illustration. 2 % Model 2 3 “E Model 3 4 ._§ Model 4 Are you sure? DEVCI 4 2E 7 77 cleUenlion Welcome to use the DEVO 12E transmitter DEVCI 1 2E Press ENT to transmit, “Transmitting ...... " appears in the interface. . M IT t Or press EXT to exitPress EXT to exit after another DEVO 125 we ransm' received the data. ¢4 e: “mm a No. 1 Transmitting- I I I (2) Model receiving Press ENT to enter Main Menu and press UP or DN to select Model Menu. Press ENT to enter Model Menu and press UP or DN to select Model Receiving, continue to press ENT to enter Model Receive setting interface. An enquiry information “Are you sure?" will be shown as below lllustration. Press ENT to receive. Model Receive Model Receive “Connecting......" and “Receiving ...... " will be shown in series in the interface. The information of “Received" with Are you sure? the model name will be shown after receiving is finished. Or press EXT to exit. Model Receive Connecting I I I I Press UP or DN to choose Model Receive Model Receive the save position. an enquiry V1 N Model 1 I information “Are you sure?" is shown after press ENT. 2 ’-§ Model 2 Model1 Press ENT to save or press 3 ,_§ Model 3 o EXT to exit. Are you sure. 4 ’-§ Model 4 2.5 Model reset All the model data can be restored to factory settings via Model Reset. Press ENT to enter Main Menu and press UP or DN to select Model Model Reset Illl Menu. Press ENT to enter Model Menu and press UP or DN to select M d IAII Model Reset, press ENT to enter Model Reset setting interface. ° e I It is possible to store up to 30 models data in the model list of DEVO- “1 N Model 1 12E equipment. There are two methods to reset the model data: batch 2 ’-§ Model 2 reset and single reset. 3 ’-§ Model 3 Batch reset: press UP or DN to select All Models, an enquiry information"are you sure?" will be appears in the interface. Press ENT to reset all models, or press EXT to exit. Model Reset Model Reset Single reset: Press UP or DN "MM All to choose the model you want No. 1 to restore, “Are you sure?" will Model 1 appear after press ENT. Press ENT to reset or press EXT to exit. Model All Are you sure? Are you sure? 2.6 Type Select This device offers three model types menu. They are Helicopter, Airplane and Glider respectively. Press ENT to enter Main Menu and press UP or DN to select Model Type Select Menu. Press ENT to enter and press UP or DN to select Type Select _ and press ENT to enter setting interface. Helicopter Press “ENT" button to get Helicopter. Airplane and Glider selections Airplane. -- and press UP or DN to select and press ENT to confirm, then press EXT to exit. 9' DEVD 1 EE 7 7B oleUention DEVD 1 2E Welcome to use the DEVO 12E transmitter 2.7 Trim System Trim System is able to finely tune the followmg six items, respectively: Elevator, Aileron, Rudder, Spoiler, Left Trim and Right Trim. The trim range is diVided into 20 grades (factory default is set at4). it is convenient to subtly modify the pitch by adjusting the trim range. Trim System Press ENT to enter Main Menu and press UP or DN to select Model Menu. Press ENT to enter and press UP or DN to select Trim System, Elevator press ENT to enter setting interface. 4/20 Press UP or DN to select the trim which will set, press R to increase Aileron the trim value and press L to decrease. 4/20 Trim System For elevator, aileron, and rudder, there are two more options: Normal Elevator and Limited, press R or L you can change the setup. “Normal" means the trim is always working although the corresponding stick stays anywhere. “Limited" means the trim is out of working when the corresponding stick is at maximum position. m Press EXT to exit after finished. Aileron 2.8 Stick Position Switch According to the following setting, the switch can be used as a switch. The turn-on or turn-off position at which stick stays can also be settable. Method for setting: Press the ENT to enter Main Menu and press UP or DN to select STiCk POSWW SW--- Ellll Model Menu. Press ENT to enter Model Menu and press UP or DN Switch to select Stick Position Switch, press ENT to enter Stick Position Switch setting interface. m There are four options under the Stick postion sWitch: SPSO, SPS1, Channel SPS2,SPS3. Press R or L to choose the switch you want to define. Inhibit Press UP or DN to inhibit channel in naVigation mark, and press R to expand the menu.The channel includes four items: Elevator. Aileron, Spoiler and Rudder. The factory default is Inhibit. Take Elevator for example. SliCk Position 5W" :iiii SliCk POSifiOF‘ 5W--- :iiii Press R or L to choose the SWitch I Position I ElFevatoDLats stick, then-Prle-ss SPSO SW or 0 move nagiva ion mark to value of position. Its Channel possible to adjust the stick m On Up position via pressing R or L. Press UP or DN to navigate the On setting, press R or L to change the direction of the channel stick. Stick Position SW... llll Stick Position SW... illl fifsss‘alilj’sovrvaghtzan::lg::: Position Status “ the sketch map of the stick 0% On On/Off direction. Check if it On I / was set correctly. K Off I After finished the setting, “ press EXT to exit. 2.9 Device select This setting can help you configure various functional switches, or adjust levers. It includes Flight Speed Switch, Flight Launch Switch, Aileron and Rudder Trim, Flap Trim, Flaperon Trim. DEVD ’l 2E 778 deUeniion DEVD 1 2E Welcome to use the DEVO 12E transmitter Press ENT to enter Main Menu. press UP or DN to move naVigation mark to select Model menu. Press ENT to enter Model menu function. Press UP or DN to Device select Option. Press ENT to Device select Flight Speed SWitch Option interface. m (1) Flight Speed Switch: _ _ Flight Launch SWItch Press UP or DN to move navigation mark to Flight Speed Switch and Inhibit press R or L to select the deSired switch. The factory default setting is Inhibit. (2) Flight Launch SWitch: Press UP or DN to move naVigation mark to Flight Launch SWitch and press R or L to select the desired sWitch. The factory default setting is Inhibit. Device Select Device Select Launch Reverse: Press UPor UN to move navigational mark to "Launch _ _ Reverse" setting after you select the Flight Launch Switch, press R Fl'ght Launch SW'tCh or L to Normal 0r Reverse. The factory default is Normal. Inhibit I Launch Reverse (3)Aileron and Rudder Trims m There are two options: Common and Flight Mode. In Common option, the adlustment parameter, of which the stick is corresponding to trim, puts an equal effect on all the flight modes In Flight Mode, the adjustment parameter,of which the stick is corresponding to trim, puts a respective effect on the corresponding flight mode. The factory default setting is Common. Device Select Press UP or DN to move navigational mark to "Aileron and Rudder Trim" , press R or L to select Common or Flight Mode. The factory Aileron and Rudder... default is Common. m I (4) Flap Trim: Refer to "(1) Flight Speed Switch". Flap Trim Inhibit (5) Flaperon Trim: Refer to "(1) Flight Speed Switch". After finished the setting, press EXT to exit. 2.10 Device Output Device output is composed of eight items. It can set up output switches and select the usage of levers, respectively. It can also Active, Inhibit or use other functions. Device Output Press ENT to enter Main Menu, press UP or UN to move naVigationaI mark to Model Menu. Press ENT to enter Model menu. Press UP or Gear DN to select "Device Output" and press ENT to enter "DeVice Output" m interface. Below eight items can be adiusted: Motor, Flap, AUX2, AUX3. AXU4, AUXS. AUXS. and AUX7. Function Active (1) Motor Press UP or BM in Device output interface can change the "Motor" switch. It includes FMOD SW, MIX SW, ELEV D/R, AILE D/R, RUDD D/R, GEAR SW, SPSO SW, SPS1 SW, SPSZ SW, SPSS SW, Left Trim, Right Trim, AUX4 KB, AUX5 KB, AUXG KB, AUX7 KB, Spoiler Stick. Press R or L to select the setting switch, The default setting is GEAR SW. DeVice Output Gear I Press UP or DN to select Function Setting after you select the switch, m Press R or L to select Inhibit. Active, Gyro. The default setting is Active. You can continue to set other items after finishing. Function Active DEVO 1 EE 7 BO deUeniion Welcome to use the DEVO 12E transmitter DEVD 1 EE (2) Flap Press UP or DN to move navigational mark to Flap. Press R or L to DEVICE OUtPUI DIIII expand the menu including FMOD SW, MIX SW, ELEVE DIR, AILE Flap D/R, RUDD D/R, GEAR SW, SPSO SW, SPS 18W, SPSZ SW, SPS3 m I SW, Left Trim, Right Trim, AUX4 KB, AUXS KB, AUX6 KB. AUX7 KB. Spoiler. The default setting is MIX SW. Function Function Setting: The default setting is Active. Acme (3)AUX2 Press UP or DN to move navigational mark to AUX2. Press R or I. to expand the menu including FMOD SW, MIX SW, ELEVE D/R, AILE D/R, RUDD DIR, GEAR SW, SPSO SW, SPS 15W, SPSZ SW. SPSB SW, Left Trim. Right Trim, AUX4 KB. AUXS KB. AUX6 KB, AUX7 KB. Spoiler. The default setting is Spoiler. Device Output AUX2 Press UP or DN to select the Function setting, press R or L to choose m I the switch, it inculdes Inhibit, Active. The default setting is Active. You can continue to set other items after finished . Function Active (4) AUXS. AUX4. AUXS, AUXS, AUX7 settings please refers to the AUX2 settings. AUX3 default setting is RUDD DIR. AUX4 default setting is AUXA KB: AUX5 default setting is AUXS KB: AUXS default setting is AUXB KB; AUX7 default setting is AUX7 KB. After finished the setting, press EXT to exit. 2.11 Wing Type The Wing Type includes VrTail. Tip Ailerons. and Dual Spoilers. Wing Type selection w _ V-Tail I Press ENT to enter Main Menu, press UP or DN to move naVIgation mark to Model Menu. Press ENT to enter Model Menu. Press UP m or DN to choose Wing Type, and press ENT to enter the Wing Type Tip Ailerons interface. Inhibit (1) VeTail setting Press UP or DN to move navigation mark to "V-Tail", press R or Lto select the options, it including two options of Inhibit and Active. The default setting is Inhibit. (2) Tip Ailerons setting: The setting is same as the above. (3) Dual Spoilers setting: The setting is same as the above. (4) Dual channels setting It is possible to set Elevator, Rudder, and Flap in Dual channels, and is of tworchannel output function. The AUX channel, which will be used as Dual channels setting at DeVice Output in Model Menu, should be previously set as Inhibit (Refer to "2.10 Device Output"). (4.1) Channel setting Wing Type Dual Channels Press UP or DN to move the navigational mark to item Dual Channels in the interface of Wing Type Press R or L, there are items of Elevator, Rudder. and Flap. We take Elevator as an example. DEVD ‘I EE 781 oieUeniion DEVD 1 2E Welcome to use the DEVO 12E transmitter (4.2) Mate setting: Wing Type Dual Channels Elevator I Press UP or DN to select “Mate Channels" setting, press R or L to select the desired channel in the menu with Inhibitt and the inhibited channels previously set in “Device Output". Mate Wing Type (4.3) Trim Setting: m Mate Press UP or UN to select “Trim Channels" setting, press R or L to select the item you want to choose as trim lever in the menu with Inhibit, Left Motor trim, Right Trim, AUX4 KB, AUX5 KB, AUXG KB, AUX? KB Trim The setting of Rudder and Flap In the Item Channel are same as m above. After the setting, press EXT to exit. 2.1 2 Power Amplifier The transmission output power of DEVO 12E is adjustable. It is divided into six grades from small to big. The lower the transmission output power transmits, the shorter the radio range is. and the longer the stand- by time Will be, the higher the transmission output power, the farer the radio range, and the shorter the stand by time. Choose the appropriate transmission output power according to the actual situation. Press ENT to enter Main Menu, press UP or DN to move navigation mark to Model Menu. Press ENT to enter Model Menu. Press UP or DN to select PowerAmplifier and press ENT to enter Power Amplifier interface. Power Amplifier Press UP or DN to choose the desired output power value. Press ENT to confirm then the corresponding items will have "M"mark in front of the items. Grade 6 Grade 5 Grade4 Grade 3 i Grade 2 Grade1 20dBm 15dBm 10dBm 5dBm i OdBm -5dBm After the setting, press EXT to exit. 2.13 Fixed ID This setting Will bind DEVO 12E with its receiver in a unique corresponding relationship. It will greatly speed up the time of automatic binding when DEVO 12E power on. (1) Setting for fixed ID The setting for fixed ID should be under the status that automatic ID binding is successfully finished. Below is the setting method. Press ENT to enter Main Menu, press UP or DN to move naVigation mark to Model Menu. Press ENT to enter Model Menu. Press UP or DN to select Fixed ID and press ENT to enter Fixed ID setting interface. Fixed ID Fixed ID If you want to activate the fixed ID setting, press R or L to change the status from off to Status “ Status “ on. A series of random digits will be shown below after ID Code 326186 changing to on. Fixed ID niiii Press UP or DN to choose the ID code setting, press R or L to cause Status On the words or number. press UP or DN moves to the next code setting. there are 6 words can be set to ID code. ID Code E26186 DEVCI 1 EE 7 BE cJeUention Welcome to use the DEVO 12E transmitter DEVD 1 EE Press ENT after the new ID has been set. An inquiry interface of “Are you sure?" pop up. “ID Code Matching will be shown after press ENT. After matching, the interface will be returned to Model Menu Fixed ID Fixed ID llll Fixed ID lDMatch I I I I Are you sure? (2) Fixed ID cancellation Insert the assorted BIND PLUG into the output terminal of BATT before the receiver power on, and then plug 5V DC power into other output terminal. The red light of receiver Will flash slowly. This means the fixed ID code has been cancelled. Pull out bind plugDEVO 12E also need to make relative cancellation and reVision after the fixed ID in receiver is cleared out . In the Main interface press the ENT to enter Model Menu and then A press UP or DN to move the navigational mark to select Model Menu. H—I Press ENT to enter Model Menu. Press UP or DN to select Fixed ID I code and press ENT to enter the Fixed ID code interface.Press UP I or DN to select Status option, Press R or I. to change the status to 1 off. Then press EXT to exit. 2.14 Sensor setting Setting method: press ENT enter to the Main Menu. Press UP or DN to select the Model Menu. Press ENT enter to Model Menu. Press UP or DN to select sensor press ENT enter to the sensor setting interface. See the Illustration. Sensor Setting Sensor Status Press R or L to select Activate or Inhibit (the default setting is Inhibit), m such as press Activate Will includes No Signal Warning,Voltage sensor.Temperature sensor.GPS receiver setting etc. (1) N0 Signal Warning Sensor Setting Press UP or DN to make the navigation mark to choose "No Signal S ensor Status Press R or I. to choose " Inhibit" or “Active"(default setting Active . If you choose “Active", the Radio will alarm when telemetry No Signal Warning There are 3 different types of voltage can be measuredll includes Internal 5V.External V1 and V2 which can be monitored two different external voltage(i.e. battery) respectively.0nce the measured voltage is lower than the setting value, the Radio will alarm. signal lost. Picture as right: (2) Voltage setting (2.1) Receiver 5V(lnternal) PFV(Power Feeding Voltage) Alarmed value can be setted as 3.6-6V Voltage setting: press R or L to activate the 5V, the alarm interface will appear in the interface, please refer to the Illustration. Voltage ii i i Voltage "H Press UP or DN to select the Internal: 5v I Internal: 5V I Alarm Voltage setting,press m Active R or L to set the value. The range is 3.6-6V. you can Alarm Voltage _ _ continue to set other items after you finished. DEVD ’I BE 783 (teUenlion DEVU 12E (2.2) External V1 Welcome to use the DEVO 12E transmitter Press UP or DN enter to External V1 setting interface. Press R or L to activate the V1. the details refers to the Illustration. Press UP or DN to select the Voltage I i i ii Voltage D ‘ I II External: V1 External: V1 Alarm Voltage Alarm Voltage 0-“ Alarm Voltage setting. Press R or L to set the value. The setting range is 0.2~99.9V. you can continue to set other items after you finished. (2.3) External: V2 setting can refer to External V1 setting. Press EXT back to sensor setting interface after you finished. (3) Temperature sensor The temperature sensor can measure up to 4 different temperature(i.e.motors).You can choose Celsius or Fahrenheit.The alarmed value can be setted to 4 different temperature.0nce the measured value is higher than the setting value, the radio will alarm.The Alarm Temperature value can be setted as 720~220'C or —4.0~428.0" F. _ Temperature in I i ii Temperature Setting: —m . . Unit In the “Sensor Setting"interface, press UP or UN to make the naVigation I mark to choose "Temperature Sensor", and press ENT to enter T1 Inhibit “Temperature Sensor"set'ting interface. See the illustration. T2 Inhibit (3.1) Unit Press UP or DN to make the navigation mark to choose “Unit"setting item,and press R or L to choose Unit, two kinds of Unit:Celsius and Fahrenheit. (3.2) Alarm Temperature settings Press UP or DN select the T1 .Press R or L to Active the setting. Inhibit Will change to Active and Alarm temperature Will be shown. If you choose Inhibit, the Alarm temperature value won’t be shown. Tem erature Press UP or DN to select “Alarm"setting, press R or L to set the alarm p temperature value. Press UP or DN to set other items after finishing Unit the setting. T1 Alarm (3.3) T2, T3, T4 setting T2 Refer to the step of “(3 2)T1 (4) GPS setting GPS Setting Dl|l| There are 4 items including Altitude Type,Speed Unit, Date Type and Altitude Type Time Zone in the GPS receiver setting interface. Absolute Press UP or DN to select the Sensor setting interface to enter the Speed Unit GPS setting interface. Knots (4.1 ) Altitude Type Press UP or UN to select the Altitude type on the GPS setting interface and it’s Absolute and Relative. (4.2) Speed Unit GPS Setting ul||| GPS Setting ul|l| Press UP or DN to select the Altitude Type Altitude Type §peed UM ”the GPS setting Relative Relative interface and it includes knots , , and km/h and relative. Select Speed UM Speed U"" the desired item- m DEVD 1 EE 7 84 Welcome to use the DEVO 12E transmitter (4.3) Date Type oieUeniion DEVD 1 EE Press UP or DN to select the Date Type on the GPS setting interface and it includes DD-MM-YY,MM-DD- YY and YYVMMVDD. Select the desired item. GPS Setting GPS Setting (4.4) Time Zone Date Type DD-MM- Time Zone UTC+08:00 Date Type DD - MM - YY Time Zone UTC+08 0 Press UP or DN to select the Time Zone , press R or L to I set the desired Time Zone. Function Menu can help you custom adiustments tor the selected models. The menu includes such items as Reverse Switch, Travel Adjust, Sub Trim, Dual Rate and Exponential, Motor Hold, Flaperon Mix, Camber System, Differential, Balance,Gyro Sensor, Rudder to Spoiler Mix, Aileron to Rudder Mix, Elevator to Flap Mix, Aileron to Tip Aileron Mix, Flap Rate, Brake System. Program Mix, Monitor, Fail Safe, Sensor View. Trainer and Timer. Reverse Switch 3.1 Reverse Switch Press ENT to enter Main Menu; Press UP or DN to move the navigation Elevator mark to Function Menu, and press ENT to enter Function Menu. Press UP or DN to choose Reverse Switch and Press ENT to enter Reverse Switch interface. R-Aileron Press UP or DN to move navigation mark to ELE(take Elevator for example), press R or L to shift the status between nomal and reverse. These are two status for option. And the default setting is Normal. All Channels Reverse Switch like: R-Aileron, L-Aileron, Rudde, Motor, Flap, AUX2. AUX3, AUX4, AUXS, AUX6 and AUX7 can be referred to the way of ELEV Reverse Switch. And press EXT to exit after finishing setting Reverse Switch Elevator Reverse R-Aileron Normal 3.2 Travel Adjust Press ENT to enter into Main Menu. Press UP or DN to move navigation mark to select item Function Menu. Press ENT to enter Function Menu. Press UP or DN to select Travel Ajust, Press ENT to enter Travel Adiust interface, as below illustration. It shows the Travel Adiust status of one channel: Take Elevator for example, Press UP or DN to move navigation mark to desired item Elevation of U. Press R or L to increase or decrease the servo travel range. The adjustment range is from 0.0% to 150.0%. The factory default is 100.0%. Press UP or DN to move navigation mark to desired item Elevation of D. Press R or L to increase or decrease the servo travel range. The adjustment range is from 0.0% to 150.0%. The factory default is 100.0%. llll Elevator I U100.0% D100.0% Travel Adiust All other channel's Travel Adjust like R-Aileron. L-Aileron, Rudder, Motor. Flap. AUX2, AUXS. AUX4, AUXS. AUX6 and AUX7 can be referred to Elevator travel Ajust. Press EXT to exit after setting finished. DEVC} ‘l EE 7&5 JeUention DEVO 1 2E Welcome to use the DEVO 12E transmitter 3.3 Sub Trim Sub Trim can move the neutral point of the servo But we advise you to mechanically adjust the servo bell crank it offset is far away from the neutral point of servo, because excessive usage ofthe sub trim may damage the servo. Sub Trim Setting method: — Elevator Press ENT to enter Main Menu, Press UP or DN to move the naVigation / mark to select item Function Menu. Press ENT to enter Function Menu, Press UP or DN to select Sub trim, and press ENT to enter Sub Trim RrAileron interface. The interface show the items and the channels which are adjustable. Press R or L to change the neutral point of Servos. The factory default is 0.0%. Press UP or UN to choose desired items. The range as below: Channel name Adjustment range Channel name Adjustment range Elevator 062.5% ~ U62.5% -62.5% ~ +62.5% R-Aileron R62.5% ~ L62.5% AUX3 -62.5% ~ +62.5% L-Aileron R62.5% ~ L62.5% AUX4 -62.5% ~ +62.5% Rudder R62.5% - L62.5% AUXS -62.5% ~ +62.5% Motor 62.5% ~ +62.5% AUX6 -62.5% ~ +62.5% Flap D62.5% ~ U62.5% AUX7 432.5% ~ +62.5% Press EXT to exit after adjustment finished. 3.4 Dual rate and Exponential After this function is set up. it is possible for DIR switches to control the dual rates of elevator. aileron and rudder, respectively. The setting range is covered from 0% to 125%. Under the help with exponential curve adjustment, it is possible to make both customized setting and automatic setting. The switch between Dual rate and Exponential can be performed via pushing or putting the Flight Mode Lever. Press ENT to enter Main Menu. Press UP or UN to move navigation Dual Rate and EX--- Uliii mark to deSired item Function Menu. Press ENT to enter Function . . Channel r Menu, press UP or DN to choose Dual rate and Exponential, Press ENT to enter DIR and Exponential interface. m (1) Channel selection Position Pos 0 J Press UP or DN to move navigation mark of Channel, Press R or L to set up channels containing Elevator, Aileron and Rudder. Choose the desired channel for setting. (2) Position selection Press UP or DN to move navigation mark to desired item Position. In the manual mode, the function of Dual rate and Exponential will be executed by the corresponding D/R sWitcn among PosO and Post. Take the item Elevator at channel as an example. It’s possible to shift between P050 and Post Via pushing or putting the D/R sWitch. ' o A e A Dual Rate and EX .. iiii (3) Dual rate adjustment Position .- Pos 0 I Press UP or DN to move the navigation mark to desired item Dual Dual Rate Rate. It's possible to change the Dual Rate value of Postion via ,, pressing R or L and the corresponding value curve in the right top H ' J of interlace Will be changed accordingly. The factory default is 100%. DEVD 1 EE 7 BB
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 10 Producer : GPL Ghostscript 8.15 Create Date : 2014:04:15 15:26:01 Modify Date : 2014:04:15 15:26:01 Title : DEVO-12E manual.PDF Creator : PScript5.dll Version 5.2.2 Author : FrankEXIF Metadata provided by EXIF.tools