GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual

Download:
Mirror Download [FCC.gov]
Document ID	2246013
Application ID	vhhzY35Of3si6HJEbqniHA==
Document Description	Users Manual part 8 of 11
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	355.84kB (4448058 bits)
Date Submitted	2014-04-18 00:00:00
Date Available	2014-04-18 00:00:00
Creation Date	2014-04-15 15:25:06
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2014-04-15 15:25:06
Document Title	DEVO-12E manual.PDF
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Frank

oleUention
DEVU 1 EE
Welcome to use the DEVO 12E transmitter
(5) Switch Selection
When the item Throttle Stick is set in Inhibit. it is possible to switch between Pos 0 and P05 1 by SWitch.
Press UP or DN to select “Switch". Press ENT to enter Switch interface, press UP or DN to choose desired
item. Press ENT to confirm. the desired item whose left side Will be changed into “1" from “".0 If two or more
items are selected. the item . .
And should be selected. Pitch Curve SW'mh EH“
whose left side should be Throttle Stick
changed into “1" from ““.O Inhibit .
Press EXT after finished it. @ thm Mode 0
SWitCh @ Flight Mode 1
IE] tiémsm I © FlightModez
3.17 Program mix
There are 8 series of program mix. mix channels and values are adjustable.
Setting Method:
Press ENT enter to Main Menu. Press UP or DN select function. press
ENT to enter function menu, then press UP or DN select “Program
Mix". And press ENT to progiam Mix setting and current status (default
setting is “Inhibit") interface. Press R or L to choose Inhibit. Normal
or Curve.
Program Mix
ll l l
Program Mix 1 I
Take “program mix 1" for example. there are “Normal" and “Curve"
setting.
(1) The “Normal" setting of “program mix"
Press UP or DN select the “Normal"setting. Press ENT button then pop up “All Servos Hold?" Press R or L
to choose OK or Cancel. If
“OK" selected. all the servos
will be locked in the current
status. if “Cancel" selected. all
servos are unlocked. Press
ENT enter to Program mix
Program Mixl uiiii
Program Mix‘l :iiii
All Servos Hold?
OK cancel
Master I
Slave
setting interlace. Elevator
Master : i i i i
J Elevator I
Aileron
(1.1) Master channel setting
Press UP or DN to move the navigatioal mark to select Master option
and press ENT to Master interface. Press UP or DN to select the
Throttle desired channel and press ENT to make a “V”. Press EXT to be back
Rudder to Program Mix 1 interface.
(2) Slave channel setting Slave Ellll
Press UP or DN to move the navigatioal mark to select Slave option .1 Elevator
and press ENT to Slave interface. Press UP or UN to select the desired
channel and press ENT to make a “V“ Press EXT to be back to Program Aileron
Mix1 interface. Throttle
(1.3) Gain setting: Take Elevator at Master as an example. Rudder
Program Mix 1 (1.3.1) Pos 0 UP:
Pos 0 Up
Mix amount setting when elevator slick moved upward.
Press UP or DN to move the navigational mark to select "Pos 0 Up"
item. Press R or L to increase or decrease. separately. the mix
amount it is possible to reverse mix direction through changing the
plus or minus sign before amount. The adJustable range is 1125%.
Pos 0 Down
O"/
DEVD 1 BE 7 67
cleUethion
DEVD 12E
Welcome to use the DEVO 12E transmitter
(1.3.2) Pos 0 Down:
Mix amount setting when elevator stick moved downward.
Press UP or UN to move the navigational mark to select "Pos 0 Down" item. Press R or L to increase or
decrease. separately, the mix amount. lt is possible to reverse mix direction through changing the plus or
minus sign before amount. The adJustable range is :125%.
(1.3.3) Pos1 Up. Pos 1 Down setting method refer to (1.3.1) Pos 0 Up setting.
(1.3.4) Offset Setting
This function can make Slave begin to mix through the corresponding Lever SWitch from a certain point as
the starting point.
Program Mix 1 till“
Press UP or DN to move the naVigational mark to select "Offset" item. —
Press R or L to increase or decrease, separately. the mix amount. It Offset
is possible to reverse Offset direction through changing the plus or
minus sign before amount. The adJustable range is :100%. _ I
Throttle Stick
lnhibit
pmgram Mix 1 [W (1.4) Throtte Stick
Offset The switch between Pos 0 and P05 1 can be realized by setting the
0% position of throttle stick. Press UP or DN to make navigation mark
Throttle Stick to select "throttle stick" setting. press R or L to change the value or
I inhabit. Change value can set throttle stick postion.The default setting
m is “inhabit”. The adjustable range is from 0.0% to 100.0%
(1.5) Switch Selection
When the item Throttle Stick is set in Inhibit. it is possible to switch between Pos 0 and Pos 1 by SWitch.
Press UP or DN to select “Switch". Press ENT to enter Switch interface. press UP or DN to choose desired
item. Press ENT to confirm. the desired item whose left side Will be changed into “1" from “".0 If two or more
items are selected. the item
And should be selected. w SWitCh Elm
whose left side should be Throttle Stick
changed into “1" from “"0. Inhibit -
Press EXT after finished it. S t h © thm Mode 0
W C @ Flight Mode 1
I23- I ©
(2) Setting Method for Curve in Program Mix1
Press UP or DN to select Curve. press ENT to confirm. Then the interface pop up "All Servos Hold?". press
R or Lto choose OK or Cancel.
If select OK. all the servos Will Program Mix 1 Ellll Program M‘X1 ”ll“
be locked in the current status. Master 9 . .2 I
if select Cancel. all servos are
unlocked. Press ENT to setting A“ Servos "Old?
interface of program Mix1. OK Cancel Slave
Elevator iléMééPi
Master E l l l l
J Elevator I
(2.1) Master channel setting
Press UP or DN to move the navigatioal mark to select Master option
and press ENT to Master interface. Press UP or DN to select the
Throttle desired channel and press ENT to make a “"‘1. Press EXT to be back
Rudder to Program Mix 1 interface.
Aileron
DEVU 1 EE 7 SE
Welcome to use the DEVO 12E transmitter
cJeUention
(2.2) Slave channel setting
DEVD 1 2E
Press UP or DN to move the navigatioal mark to select Slave option and press ENT to Slave interface. Press UP
or DN to select the desired channel and press ENT to make a “V". Press EXT to be back to Program Mix1 interface.
Slave ii i i Program Mix 1
J Elevator I Position
Aileron m
Throttle Exponential
Rudder Off
tiéMéAfi
Hi I (2.3) Position
There have two options:Pos
O and P05 1.Press “UP" or
“DN"to select the desired
position.
(2.4) Exponential Curve
Press UP or DN to choose the setting item of "Exponential" .There
are On or Off option when you press the R or L buttoms. Select On
for smooth changes, and Off for changes in the form of fold ling in
Exponential curve, respectively.
Program Mix 1
Position 9- ~01
Pos 0 I
Exponential
timm
Program Mix 1
Exponential
Off
Point
(2.5) Point Setting
Press UP or DN to move the navigation mark of Point option. Press
R or L, there are 7 piont options including "PointrL","Pointr1”. "Point,
2", "Point-M", "Point-3", "Point -4" and "Point-H". Select the point you
want to set.
ti mm
(2.6) Status setting
(There is no Status options when the piont is Point-L or Point-H) After
selecting the point that you want to set, press UP or DN to move the
naVigational mark to Status item. Press R or L. there are two options
of Inhibit and Active. Select Inhibit for unchanging the current amount
(the default setting is Inhibit).
Program Mix 1
Point .9- ~9i
Point - 1
Status
M ii mm
Program Mix 1
Output
Switch
L.. ..4
0" L12M34H I
(2.8) Throtte Stick
(2.7) output setting
When the Status option is Active, the Output option will be IistedPress
UP or DN to move the navigational mark to Output. Press R or L to
increase or decrease, respectively, the output amount. It is possible
to reverse the mix direction by changing the plus or minus sign before
the amount. The adjustable range is :100%.
Program Mix 1
The Switch between Pos 0 and P05 1 can be realized by setting the
position of throttle stick Press UP or DN to make navigation mark
to select "throttle stick" setting, press R or L to change the value or
inhabit. Change value can set throttle stick postion.The default setting
is “inhabit". The adjustable range is from 0.0% to 100.0%
(2.9) SWitch Selection
When the item Throttle Stick is set in Inhibit, it is possible to switch between Pos 0 and P05 1 by SWitch.
Press UP or DN to select “Switch". Press ENT to enter Switch interface, press UP or DN to choose desired
item. Press ENT to confirm, the desired item whose left side Will be changed into “1" from “"0. If two or more
Throttle Stick
Switch
Pos 0
Lizivi34H
items are selected. the item
And should be selected,
whose left side should be
changed into “1" from “".0
Press EXT after finished it.
Program Mix 1
IIII
Throttle Stick r. » .1
Inhibit
SWitch
L12M34H
a:
:r
© Flight Mode 0
© Flight Mode 1
© Flight Mode 2
DEVD 1 EE 768
deUeniion
DEVO 12E
Welcome to use the DEVO 12E transmitter
3.18 Monitor
This function can display the current status and positions of all the channels' outputs, and check the current
working status of each channel.
Monitor
Press ENT to enter Main Menu, and then press UP or DN to move
the navigational mark to select Function Menu.Press ENT to enter
the Function Menu and then press UP or DN to select servo Monitor E|—.——.—.—.—I I:|:I
and press ENT to enter the monitor interface for checking the current I:I:I |:|:|
working status of each channel Press EXT to exit . l:l:l l:|:l
3.19 Fail safe
There are two possibilities for use if the transmission signal is under abnormal condition. The first one is to
lock the last action data received: the second one is to execute the preset data which is preeset. The default
setting is Servo Hold.
Setting method: Fail Safe ”ll”
Press ENT to enter the Main Menu, and then press UP or DN to move Elevator I
the navigational mark to select Function Menu Press ENT to enter Servo Hold
the Function Menu then press UP or DN to select Fail Safe and press
ENT to enter the Fail Safe interface.Take the item Elevator as an
example to explain.
Press UP or DN to select Elevator on the Fail Safe interface. then press R or L to change the status of Servo
Hold into Fail Safe(lf you want to keep Servo hold status, there is no need to re-set). There is a expanded
sub-item blow. Press UP or DN to select 0%, then press R or L to increase or decrease, respectively, the
position amount which centers on the neutral point of servo. The available value is 125%, respectively. 0%
is the neutral point of servo.
F3" Safe Ellll The setting methods for other channels are same as above.
Elevator I Press EXT to exit after finished.
Fail Safe Note: checking whether all the actions when fail safe happened are
correct, is a must afler the setting is finished. It is dangerous to use
full throttle, especially after fail safe taken place.
3.20 Sensor View
Setting method:Press ENT to enter the Main Menu and press UP or DN to move the navigational mark to
select Function Menu.Then press ENT to enter the Function Menu and press UP or UN to select Sensor
View, then press ENT to enter the Sensor View interface, like below pictures. If all the sensors disconnect,
telemetry signal lost, there Will be inhibits shown on the view. If all work normal, all the measured data will
be shown.
(1) Voltage:Show 3 diffierent measured voltage value;
Voltage [iiii Voltage :iiii
inhibit I 5.3 Unit I
Inhibit 8.3 Unit
Inhibit 0.0 Unit
(2) Temperature: Show 4 different measured temperature value;
Temperature : i i ii Temperature : i i ii
Inhibit 7B'C
Inhibit I r7'c I
Inhibit *9'C
Inhibit *7'C
DEVD 1 EE 7 7D
oieUeniion
Welcome to use the DEVO 12E transmitter
DEVD 1 EE
(3) Rate Sensor:Show 2 different measured RPM value;
Rate Sensor E i i i i Rate Sensor : I i ii
Inhibit 5000RPM
Inhibit I 4000RPM I
(4) GPS Sensor:Press UP or DN to turn to GPS function. show located date, time, longitude, latitude, altitude
and speed;
GPS Sensor [iiii GPS Sensor [iiii
Irihlbit East 113“ 23.7120
Inhibit North 22° 53.4805
Inhibit 73.7 m
Inhibit ! 0.0 km/h !
3.21 Trainer
Two DEVO 12E transmitters working together can execute the training function to meet the requirements for
the beginner. The setting method is shown as below:
(1) Data copy
First, use the wireless copy function between two DEVO 12E to copy the main transmitter‘s model data to
the trainee's transmitter. this promise the model data between two transmitters is same. Refer the copy method
to the second part of helicopter “2.4 model wireless copy" and do the followmg steps:
(2) Linkage Linkage icon at trainee‘s DEVO 1257
Insert the signal wire from the trainer’s transmitter into the DSC
socket of the trainees transmitter Turn on the transmitter and a JeUeniion
linkage icon will be shown on the boot screen. 1 mo,
. ' 00:00
0.0%
DSC socket . DSC socket .
. .
‘— ‘—
Digital signal wire Digital signal Wire
linkage icon
Turn on the power of the trainer's radio. Find out the trainee‘s model data, and then let the trainer‘s Radio
bind with the aircraft model and fly it normally. Then turn off the power.lnsert the other end ofthe digital signal
wire into the trainer's DEVO 12E, and then turn on its power. A linkage icon will be shown as below:
Trainee is on and trainer is working Trainee is working and tralner is on
(4 ¥ ti X riiiiriiiill A ¥ Cw viiiiriiiiil Trainer icon
6 6,”,ng Model 1 6 egg: Model 1 Training status display: when the trainer’s
00-00 0000 icon becomes into “)IC', the trainee stops
& & flying and the trainer is working; when the
00% 00% trainer‘s icon turns into'v". the trainee is
flying and the trainer is in leisure.
DEVD ’l EE 771
deUethion
DEVD 4 2E Welcome to use the DEVO 12E transmitter
(3) Usage method
Right Trim
The training switch can be freely SWitchable between Left
trim and Right trim. The default setting is Right trim. See 3 I i - i . 1
the right illustration:
During flight, if the trainer pushes Right Trim once, the linkage
icon will be shown as "«/" that means the control right is moved ‘ 3
to the trainee from Trainer. lf trainer pushes Right Trim once A 9 ‘
again, the linkage icon will be shown as “X" that means the trainer takes back the control right from the trainee.
(4) Setting for training function channels
Trainee is available to get full or part of flight control power to the aircraft model via setting the training function
channel in the trainer's radio. Below is the setting method:
Trainer E|lll
Press the ENT to enter Main Menu, and then press UP or DN to move
the navigational mark to select Function Menu. Then press ENT to Switch
enter the Function Menu and press UP or DN to select “Trainer" ,
then press ENT to enter the Trainer interface. The available channels Elevator
are shown below, and the current status of trainer switch is also
shown there.
Inhibit
Trainer switch selectionzPress UP or DN to select the switch option; press R or L to select the sWitch which
you want. It includes right and left trim.The default setting is Right trim.
Channel selectionIPress UP or DN to select the channel option; Press R or L to select the channel(s) which
you want to grant to trainee. The channel(s) you have selected will be activated as “Active". The channels
which are not granted to trainee will be kept inhibited. The default setting is “Inhibit". Press EXT to exit
3.22 Timer
There are two timers which can be set as stopwatch and countdown, respectively. Each timer can be operated
by sWitoh or by shortcut.
Press ENT to enter Main Menu, and then press UP or DN to move
the navigational mark to select Function Menu. Then press ENT to
enter the Function Menu and press UP or DN to select "Timer", then
press ENT to enter Timer interface. The timing range of stopwatch
is from 0 to 59:59 (59 minutes 59 seconds).The default setting is
stopwatch.
(1) Countdown setting
If you need countdown time manner, press R or L to select the
countdown.There is an expand subemenu set time item.Press UP or
UN to move the navigational mark to select the option of Seting time
item. Press R or L to set the countdown time. The settable countdown
time range is from 00:05 to 59:55.
(2) Switch selection
Press UP or UN to move the navigational mark to Switch.There are inhibit and available switch options,
available sWitch can be selected by press L or R. It includes FMOD1,2, FMODZ, MIX1,2, MIX2, ELEV D/R,A|LE
D/R, RUDD D/R, GEAR SW, SPSD SW, SPS1 SW, SPSz SW and SPS3 SW. We can select the desired
item except these items of SPSO SW, SPS1 SW, SPSZ, and SPS3 which should be previously set at Stick
Position Switch at Model Menu(refer to “2.8 Stick Position Switch"). Press EXT to exit after finished.
(3) Usage of timer U {
oe en IOH
Press UP or DN in main panela. It's possible to start Timers by 2.45m
pressing UP key for one time, and to pause it by pressing it the second 00 3 00
time. Press DN to clear timer. It's ok to control time by Switch when LTimer ; E ?
time setting is finished on switch. Timer Will be shown in main interefaoe, 0 0 %
as right illustration:
DEVD 1 EE 7 72
Part four
Glider
AeUen ion
DEVCJ ’| EE
All the functional settings, which are relative to the
operation system of DEVO 12E itself, are fully
integrated in System Menu. They include
Language, Display, Buzzer, vibrator, Stick Mode,
Stick Direction. Stick calibration, Battery, and About.
(JeUention
DEVD 1 2E Welcome to use the DEVO 12E transmltter
.0 Syste Menu
All the functional settlngs, whlch are relatlve to the operation system 0' DEVO 12E itself, are Vully integrated
in System Menu. They include Language, Display. Buzzer, Vlbrator, Stick Mode, Stick Direction,Stick calibration,
Battery, and About
Below is the boot screen of Glider:
Elevalurtrlm Spoller stick trlm
Transmlssion power dlsplay
Battery volume
Cl U J[. display
e en lon
2 .46 Hz Model name
Timer display 0 0 - 0 0
Model type
display
Rudder trim dlsplay :ilerlon trim
lsp ay
1.1 Language setting
Press ENT to the Maln Menu, press UP or DN to select System Menu, then press ENT to System Menu.
Press UP or DN to select ”Language" and press ENT to the Language
setting interface. Press UP or DN to select the language that you
want. A "\/"' will be shown on the screen after selected. Press EXT
to exit.
Language
Francais
1.2 Display
Press ENT to the Maln Menu. press UP or DN to select System Menu, then press ENT to System Menu.
Press UP or DN to select "Dlsplay" and press ENT to the Display setting interface.
DlSPIaY Ellll Three items are available to be set. Below are the setting methods
for them:
Contrast
5, (1) Backlight contrast: the backlight contrast is adjustable by pushlng
_ UP or DN to move the navigational mark to the dlgits after Contrast.
Lightness Press R key to lncrease the backlight contrast, whlle press L to
5/10 decrease it.
(2) Backllght llghtness: the backllght llghtness ls adjustable by presslng UP or DN to move the naVIgatlonal
mark the digits after Lightness.The power consumption Wlll be increased if the backlight lightness is too
bright and the battery cruise duration Wlll be shortened.Press R or L to increase ordecrease the llghtness.
When the value ls one means turn off the backllght.
(3) Backllght time out: it is posslble to set the duration whlch LCD stays at highlight in the form of “Always on"
or any period from 5 to 60 seconds Wlth an interval of 5 secondsPress UP or DN to move the navigational
mark to select the diglts after Timeout. Press L to short the time of backlight duration or keep lt in the
form of “Always on" while push R or prolong the time. The maxium is 605.
Press EXT to exit.
DEVO 1 EE 7 74
Welcome to use the DEVO 12E transmitter
1.3 Buzzer warning
oleUention
DEVD 1 EE
Press ENT to the Main Menu. press UP or DN to select System Menu, then press ENT to System Menu.
Press UP or DN to select "Buzzer" and press ENT to the Buzzer setting intertace.
Buzzer : l I ll
Status
Spoiler Stick
Inhibit
(1) Status:There are On and off two status on the Buzzer interface.
Pressmg UP or DN to move the navigational mark to the status
option Press R or L to change the On or Off status It includes
Spoiler stick,Knobs Midpoint and Tone items under the status is On.
(2) Spoiler Stick: Press UP or DN to move the navigational mark to "Spoiler Stick" item then press R or L to
change the status from Inhibit to Active. When Buzzer is at the status of On, if Spoiler Stick is set as
"Active", a relative musical scale will make response when moving the Spoiler Stick. You can judge the
position of the Spoiler Stick according to the different muSicaI scales. Also, it can be set as Inhibit.
(3) Knobs midpoint: When Buzzer is at the status of On, if Knobs is set as “Active",
there is buzzer
sound when you turn the AUX4 and AUXS to the midpoint. It you don't need the buzzer sound, please
change the status to Inhibit
(4) Tone: the tone is composed of 10 grades. You can choose the favorite one according to your
interests. Press UP or DN to move the navigational mark to Tone item and press R or L to make a listening
test. Press EXT to exit.
1.4 Vibrator
The vibrator used as an alarm function to remind the users.
Press ENT to the Main Menu. press UP or DN to select System Menu. And then press ENT to t System Menu,
press UP or UN to select
Vi brator. Press ENT to Vibrator
Vibrator
[llll
Vibrator Eillll
setting interface. There are
two status as Inhibit and
Active. Press R or L to select
Active it need. Press EXT to
exit after finished.
Status
Status
1.5 Stick Mode
Press ENT to Main Menu, press UF' or DN to select System Menu, and then press ENT to the System Menu,
press UP or DN to select Stick Mode, and press ENT to stick Mode setting interface.
Stick Mode
Model 1
Model 3
Model 4
Stick Mode
4 Mode 1
Model 2
Model 3
Model 4
61} CE
\5/ \1/
MODE 2 and MODE 4 are
listed in left-hand throttle.
MODE 1 and MODE3 are
listed in right-hand throttle.
Stick Mode
Model 1
Model 2
Model 3
_ Model 4
QAQ
Stick Mode
Model 1
Model 2
(«’99
Model 4
Select the stick mode according to the throttle mode showing on the screen. DEVO 12E offers 4 stick modes,
please refer to “8.0 SWitches exchange between Iefl-hand and right-hand throttles. Press EXT to exit afterfinished.
DEVD ’l EE 7 75
(JeUethion
DEVD 1 2E Welcome to use the DEVO 12E transmitter
1.6 Stick Direction
Press ENT to Main Menu, press UP or DN to select System Menu, Stick Direction
and then press ENT to the System Menu. press UP or DN to select
Stick Direction, and press ENT to stick direction setting interface. Elevator
Stick Direction:There are four items available as Elevator. Aileron,
Spoiler and Rudder. Press UP or UN to select the stick which Wl” Aileron
change direction, and press R or L to change the direction. The factory
setting is Normal.
1.7 Stick Calibration
It is a function to recalibration when stick unusual.
Calibration method:
Press “ENT" to the Main Menu, press UP or DN to select System Menu, then press ENT to System Menu.
Press UP or UN to select Stick
Calibration and press ENT to
the Stick Calibration setting
interface.Press ENT to enter _ _
Calibration.and see the left ENT “7c ”'9
illustration:
Stick Calibration lIII Stick Calibration E I i ii
Stick Calibration
Clockwise or counter clockwise mechanically move the right stick and
left stick from minimum levels to maximum levels several times, and
. then return the stick to the neutral positions, respectively." will shows
ENT to Calibrate the calibration is successful after you press ENT to confirm.
Calibration Success! Press EXT to exit after finished.
1.8 Battery
Battery
Battery voltage can set up the warning value for radio battery in
lower voltage.
Alarm Voltage
Press ENT to the Main Menu. press UP or DN to select System Menu.
then press ENT to System Menu. Press UP or DN to select "Battery"
and press ENT to the Battery setting interface. Warning voltage value
can be changeable by R or L button.
1.9 About
About Ellll
Press “ENT" to the Main Menu, press UP or UN to select System Software
Menu, then press ENT to System Menu. Press UP or DN to select V 1 CA
About and press ENT to the About setting interface. a" '
Press EXT to exit after finished. Library Ver. 1.0
2.0 Model Menu
Model Menu manages all the model data saved in DEVO 12E. It includes Model Select, Model Name, Model
Copy. Model Transmit. Model Receive. Model Reset, Type Select. Trim System. Stick Position Switch, DeVice
Select. Device Output, Wing Type. Power Amplifier. Fixed ID and Sensor setting.
DEVD 1 EE 7 7E

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 10
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2014:04:15 15:25:06
Modify Date                     : 2014:04:15 15:25:06
Title                           : DEVO-12E manual.PDF
Creator                         : PScript5.dll Version 5.2.2
Author                          : Frank

EXIF Metadata provided by EXIF.tools