Leviton VRSDC Dimmers User Manual 3

Leviton Manufacturing Co., Inc. Dimmers 3

User Manual 3

PRELIMINARY
WARNINGS AND CAUTIONS:
• ON/OFFLEDforremoteloadstatus.
• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.
• Ifyouareunsureaboutanypartoftheseinstructions,consultanelectrician.
• Recommendedminimumwallboxdepthis2-1/2".
WARNINGS AND CAUTIONS:
• Disconnectpoweratcircuitbreakerorfusewhenservicing,installingorremovingxture.
•
Maximumwirelengthfromdimmertoallinstalledremotescannotexceed300ft(90m).
• Usethisdeviceonlywithcopperorcoppercladwire.
4-Zone Controller with Switch - Single Pole (One Location)
Cat.No.VRCZ4-MR,120/240VAC,50/60Hz
Incandescent-1800W–MagneticLow-Voltage-1800VA(1440W)
ElectronicLow-Voltage-1800W–Fluorescent-1800VA–Supplemental-1/2HP
INSTALLATION INSTRUCTIONS
DI-000-VRCZS-00A-X0
Tools needed to install your device
Slotted/PhillipsScrewdriver ElectricalTape Pliers 
Pencil   Cutters  Ruler
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFFONOFF
ONOFF
ONOFF
ONOFF
ONOFF
WARNING: TO AVOID FIRE, SHOCK OR DEATH; TURN
OFF POWER atcircuitbreakerorfuseandtestthatpowerisoff
beforewiring!
Step 1
Step 3
5/8"
(1.6 cm) Strip Gage
(measure bare
wire here)
Cut
(if necessary)
WIRING DEVICE:
Connect wires per WIRING DIAGRAM as follows:
• GreenorbarecopperwireinwallboxtoGreenterminalscrew.
• LineHotwallboxwiretoterminalscrewmarked"BK".
• LineNeutralwallboxwiretoterminalscrewmarked"WH".
• Loadwallboxwiretoterminalscrewmarked"RD".
Wiring Application:
Hot (Black)
Neutral (White)
Line
120VAC, 60Hz
BKWH
Green
Ground
4-Zone Controller w/ Switch
Load
RD
WH
Step 4
2
4
1
3
1.Line(Hot)
2.Neutral
3.Ground
4.Load
Identifying your wiring application (most common):
NOTE:Ifthewiringinyourwallboxdoesnotresemblethis
conguration,consultaqualiedelectrician.
Step 2
INTRODUCTION
Leviton’sViziaRF+TMcomponentsaredesignedtocommunicate
witheachotherviaRadioFrequency(RF)toprovideremotecontrol
ofyourlighting.UsingRFtechnologyallowsLevitontoprovidethe
greatestsignalintegritypossible.EachmoduleinLeviton’sViziaRF+TM
componentlineisaZ-Wave®enableddevice.InaZ-Wave®network,
eachdeviceisdesignedtoactasarouter.Theserouterswillre-transmit
theRFsignalfromonedevicetoanotheruntiltheintendeddeviceis
reached.Thisensuresthatthesignalisreceivedbyitsintendeddevice
byroutingthesignalaroundobstaclesandradiodeadspots.This4-Zone
ControllerismeanttocontrolspecialzoneenabledZ-Wave®products.
Tocontrolgroupsofdevicesthataremixedordonotsupportzone
commandclassusetheLeviton4-ZoneController(VRCS4).Settingup
thisdevicerequiresspecicadvancedcontrollerfunctionalities,your
controllermustbeabletoassociatedevicetogroupsandmustbeable
tocontrolthezonecontrollercongurationcommandssuchasthe
advancedProgrammingRemote(VRCPG).
• SwitchON/OFF
• ZoneCapable
• ThisisaZ-Wave®Controller
• Zonecontrolwithouttravelerwires
• Cancall4zones
• Cancontrolasingleload
• ON/OFFLED
• Twowaycommunication
• RFreliability
• Easeofinstallation–Nonewwiring
• CompatiblewithotherZ-Wave®enableddevices
FEATURES NOTES:
• Ifusinganon-LevitonProgrammer/Remote,refertothe
Programmer/Remoteinstructionsheet.
• 4-ZonecontrollersincudedintoaZ-Wave®networkmustbeupdated
afteryouhaveincludedallotherdevices.
• IfusingtheVRCPGInstallChecklistfeature,gotostepC.
A) IfusingaLevitonZ-Wave®Programmer/Remote,Cat.No.VRCPG,
presstheMenubuttonandscrolldowntoSystemSetup.Press
thecenterbuttontoselectSystemSetupMenu.ChooseAdvanced
Settings.PressthecenterbuttontoselectNetwork.Pressthecenter
buttonto<IncludeNode>.
B) IfusingVRCPGProgrammer/Remote,youwillbepromptedtoplace
4-Zonecontrollerintoprogrammingmode.
C) ToaccessProgrammode,pressandhold
buttons1and3(refer to figure).Wait
5secondsuntiltheLEDturnsAmber.
ReleasethebuttonsandtheLEDwillblink
Amber.YouarenowinProgrammingmode.
NOTE:IftheLEDonthe4-Zonecontroller
turnssolidRedwhileincluding,therehas
beenacommunicationerror.
D) Whilestandingclosetothe4-Zone
controller(approximately1ft.),pressthe
centerbuttonontheProgrammer/Remote
to<Include>deviceinthenetwork.
NOTE:Onlyonedevicemaybeincludedat
anytime.
E) ThePrimaryProgrammer/RemotewillassignaHomeIDand
NodeIDforthisdevice.
NOTE:ThisinformationwillbestoredintheProgrammer/Remoteto
beusedforfuturereference.
NOTE:Youmaynameoredityourdeviceatthistime.
F)
The 4-
Zo
ne controller is now installed in the network. If using
VRCPG you will be prompted to include switch, otherwise, please
proceed to Step G to include switch.
Step 8 Including 4-Zone Controller with Switch
into Z-Wave® Network:
Changing the color of your device:
Your4-Zonecontrollerwithswitchincludesthreecoloroptions.The
controllershipswiththeWhiteframeattached.Tochangecolorofframe,
proceedasfollows:
Line up tabs
and press in
side to attach
Push in
side at tab
to release
Afterframeisremoved,removeexistingpushbuttonsandreplacethem
withdesiredcolorchangepushbuttons.TochangetheDIM/BRIGHTbutton,
beforemountingframe,pressoutDIM/BRIGHTbutton(bottom)frombackof
frameandpressinfromfrontofframenewDIM/BRIGHTbutton.TomakeIR
capable,replacewithaDIM/BRIGHTbuttonthathastheIRwindow.
INSTALLING YOUR 4-ZONE CONTROLLER W/ SWITCH
NOTE:UsecheckboxeswhenStepsarecompleted.
Preparing and connecting wires:
This4-Zonecontrollerwithswitchcanbewiredusingside
wireterminalscrewsorthroughbackwireopenings.Choose
appropriatewirestrippingspecicationsaccordingly.
• Positionallwirestoprovideroomin
outletwallboxfordevice.
• Ensurethattheword“TOP”isfacingup
ondevicestrap.
• Partiallyscrewinmountingscrewsin
wallboxmountingholes.
NOTE:Dresswireswithabendas
shownindiagraminordertorelieve
stresswhenmountingdevice.
• Restorepoweratcircuitbreakerorfuse.
• LEDshouldturnON.
• Togglebutton1ON/OFFtotestlocal
loadoperation.
If LED or LOAD does not turn ON,
refer to the TROUBLESHOOTING
section.
Testing your device prior to mounting in wall box:
Step 5
• Makesurethattheendsofthewiresfromthewallboxare
straight (cut if necessary).
Back Wire (either hole may be used)
Backwireopeningsaccept
#14-12AWGsolid wire copper only.
Side Wire Connection
Sidewireterminalsaccept#14-12
AWGsolid wire copper only.
Bl
Installationmaynowbecompletedbytightening
mountingscrewsintowallbox.Attachwallplate.
Device Mounting:
TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE.
Step 6
Restore Power:
Restorepoweratcircuitbreakerorfuse.
Installation is complete.
Step 7
Step 3 cont'd Step 2 cont'd
PRELIMINARY
DI-000-VRCZ4-00A-X0
©2009LevitonMfg.Co.,Inc.
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
LevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenetofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforveyearsfromthepurchasedate.Leviton’sonlyobligationistocorrectsuchdefectsbyrepairorreplacement,
atitsoption,ifwithinsuchveyearperiodtheproductisreturnedprepaid,withproofofpurchasedate,andadescriptionoftheproblemtoLeviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747.Thiswarrantyexcludesandthereisdisclaimedliabilityforlabor
forremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,overloaded,misused,opened,abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.There are no other or implied
warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and tness for a particular purpose, is limited to ve years.Leviton is not liable for incidental,
indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,whetherbasedoncontract,tortorotherwise.
Including 4-Zone Controller with Switch
into Z-Wave® Network:
Step 8 cont'd Step 9 Excluding 4-Zone Controller with Switch from
Z-Wave® Network:
For additional information, contact Leviton’s
Techline at 1-800-824-3005 or visit Leviton’s
website at www.ViziaRFplus.com
ProtectedunderU.S.PatentNumber6,388,399andpatentspending
andlicensedunderU.S.PatentsNumbers5,905,442,and5,982,103
TROUBLESHOOTING
Load Device/Switch:
• LightsFlickering
- Lamphasabadconnection.
- Wiresnotsecuredrmlyunderterminalscrewsofswitch.
• LightdoesnotturnON
- Circuitbreakerorfusehastripped.
- Lampisburnedout.
- LampNeutralconnectionisnotwired.
Controller/Zone:
• LocatorLEDoncontrollerdoesnotturnON
- Circuitbreakerorfusehastripped.
- If4-ZonecontrollerispoweredupandLEDdoesnotturnON,
 checkwiring.
• ZoneControllerdoesnotoperatelights
-Checkassociation.
 -Ensurethatcontrollerwasproperlyupdated.
- Re-programyourzone,andensureeachlightisin
thecorrectON/OFFstate.
• LEDturnssolidRed
-Checkassociation.
 -Ensurethateachdeviceinthenetworkiswithin70ft.(21m)of
 anotherdevice.
Programmer/Remote
Cat. No. VRCPG
NOTE:Programmer/Remotemustbein
closeproximityto4-Zonecontrollerwhen
includinginthenetwork.
Excluding 4-Zone controller:
A) IfusingaLevitonZ-Wave®Programmer/Remote,Cat.No.VRCPG,
presstheMenubuttonandscrolldowntoSystemSetup.Pressthe
centerbuttontoselectSystemSetupMenu.ChooseAdvancedSettings.
PressthecenterbuttontoselectNetwork.Scrolldownto<Exclude
Node>andpressthecenterbutton.
B) IfusingVRCPGProgrammer/Remote,youwillbepromptedtoplace
4-Zonecontrollerintoprogrammingmode.
C) Toaccessprogrammode,pressandholdbuttons1and3(refer to
figure).Wait5secondsuntiltheLEDturnsAmber.Releasethebuttons
andtheLEDwillblinkAmber.Youarenowreadytoexclude.
NOTE:IftheLEDonthe4-ZonecontrollerturnssolidRedwhile
excluding,therehasbeenacommunicationerror.
D) Whilestandingclosetothe4-Zonecontroller(approximately1ft.),
pressthecenterbuttonontheProgrammer/Remoteto<Exclude>
devicefromthenetwork.
Factory Default:
Ifyour4-Zonecontrollerwithswitchisnotresponding,oryouareunableto
controlitafteryouhavetriedtoInclude/Excludeitmultipletimes,itmaybe
necessarytoresetthe4-Zonecontrollerwithswitchtoitsoriginalfactory
settings.Toaccomplishthis,proceedasfollows:
• Onthe4-Zonecontrollerwithswitch(refer to
figure),pressandholdbuttons1and3.Wait
approximately10secondsuntiltheLEDturns
AmberandthenturnssolidRed.AllowLED'sto
blinkredtwice,releasethebuttons.The4-Zone
controllerwithswitchisnowreset.Oncethe
controllerisreset,itwillbenecessaryto
Re-Includeittoanetworkbeforeitcanbeused.
CAUTION:SETTINGADEVICETOAFACTORY
DEFAULTDOESNOTEXCLUDETHATDEVICE
FROMANETWORK.THEEXCLUSION
PROCEDUREMUSTSTILLBEFOLLOWEDTO
REMOVETHEDEVICEFROMTHEPRIMARY
CONTROLLER’SINFORMATIONTABLE.FAILURETODOSOMAY
RESULTINSYSTEMTHATISSLOWTORESPOND,ORMAYFAILTO
RESPONDTOSOMEDEVICES.
Zone Application:
Push Button (Default settings)
Turn ON from OFF position:
Press–Zoneisactivated,ZoneLEDturnsON.
LEDwillblinkuntilZoneisreached.
Turn OFF from ON position:
Press–TurnsalllightsinZoneOFF,ZoneLEDturnsOFF.
DIM/BRIGHT:
PressleftsideofDim/Brightbutton–LightsinlastactivatedZonewilldim.
PressrightsideofDim/Brightbutton–LightsinlastactivatedZonewill
brighten.
NOTE:ControllerwillonlyDim/Brightdeviceslocatedwithindirectradio
frequencyrange.
NOTE:LEDwillbelitonlywhenall
lightsinzonehavereachedtheir
presetlevel.Ifthereisamanual
changetoanylightinthezone,the
LEDwillturnOFFindicatingthatyou
arenolongerinthatzone.
OPERATION
LED
Push
Button
Dim/Bright
Button
G)Including local Switch:
• RemaininAdvancedSettings.
• PressCenterbuttontoselect<IncludeNode>.
• Theremotewillpromptyoutoputthedeviceinprogramming
mode.
• PutVRCZ4intoprogrammingmodefortheSwitchbypressing
buttons2and4.
• Waitapproximately5seconduntilbutton1LEDturnsAmber.
• ReleaseButtons2and4andbutton1LEDwillblinkAmber.
• WhilestandingclosetotheVRCZ4(approximately1ft.)pressthe
centerbuttonontheProgrammer/Remoteto<Include>devicein
thenetwork.
• ThePrimaryProgrammer/RemotewillassignaHomeIDand
NodeIDtoyournewswitch.
• Youmaynameoreditthedeviceatthistime.
NOTE:Bydefault,switchwillbecontrolledbyButton1onyourzone
controller.
H) Afteralldevicesareincludedintothenetwork,thecontrollermustbe
updated.Toupdatecontrollerproceedasfollows:
• Ifusinganon-LevitonProgrammer/Remote,refertothe
Programmer/Remoteinstructionsheetforupdatingcontroller.
• IfusingLevitonZ-Wave®Programmer/Remote,Cat.No.VRCPG,
presstheMenubuttonandscrolldowntoSystemSetup.
PressthecenterbuttontoselectSystemSetupMenu.Choose
AdvancedSettings.Pressthecenter
buttontoselectNetwork.Pressthe
centerbuttontoselectUpdate"cntrl".
Selectthecontrollertoupdate.Press
centerButtontobeginupdate.Update
willstartautomatically.Standwithin
(1ft)ofcontrollerwhileupdating
Networktopology.
• WaituntiltheVRCPGProgrammer/
Remoteconrmscompletion.Update
isdone.
NOTE:Ifthe4-Zonecontrollerwithswitch
hasbeensuccessfullyIncludedinthe
networkandtheusertriestoInclude
itagainwithoutrstexcludingitfromthe
network,thenodeIDwillremainthesame.
Cat. No. VRCPG
1 ON
2 ON
3 ON
4 ON
OFF
OFF
OFF
OFF
Menu
Button
Center
Button
Zone Programming:
NOTE: Alldevicesassociatedtothebuttonsmustsupport
Z-Wave®zonecommand.Ifadeviceinthegroupdoesnot
supportthezonecommanditwillnotbecontrolled.
•Pressandholddesiredzonebuttonon4-ZoneController
untilLEDblinksGreen.
•Adjustanyloadsassociatedtothatbuttonbyturning
ON/OFForDim/Brightentheload.
•Pressbuttonagainon4-ZoneControllerandtheLEDwill
stopblinking.
•Thezonehasnowbeenset.
Step 11
ThisdevicecomplieswithPart15oftheFCCRules.Operationissubject
tofollowingtwoconditions:(1)thisdevicemaynotcauseharmful
interference,and(2)thisdevicemustacceptanyinterferencereceived,
includinginterferencethatmaycauseundesiredoperationofthedevice.
Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfor
aClassBDigitalDevice,pursuanttoPart15oftheFCCRules.These
limitsaredesignedtoprovidereasonableprotectionagainstharmful
interferenceinaresidentialinstallation.Thisequipmentgenerates,uses,
andcanradiateradiofrequencyenergyand,ifnotinstalledandusedin
accordancewiththeinstructions,maycauseharmfulinterferencetoradio
communications.However,thereisnoguaranteethatinterferencewill
notoccurinaparticularinstallation.Ifthisequipmentdoescauseharmful
interferencetoradioortelevisionreception,whichcanbedetermined
byturningtheequipmentOFFandON,theuserisencouragedtotryto
correcttheinterferencebyoneormoreofthefollowingmeasures:
• ReorientorrelocatethereceivingAntenna.
• Increasetheseparationbetweentheequipmentandthereceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthatto
whichthereceiverisconnected.
• Consultthedealeroranexperiencedradio/tvtechnicianforhelp.
FCC COMPLIANCE STATEMENT
AnychangesormodicationsnotexpresslyapprovedbyLeviton
ManufacturingCo.,Inc.,couldvoidtheuser'sauthoritytooperatethe
equipment.
FCC CAUTION
After inclusion process, you must associate Vizia RF light
switches, to button on the controllers. Refer to the Primary
Programmer/Remote instruction sheet for complete
details.
NOTE:Thissteprequiresacontrollerthatcancreateassociationliststo
specicgroups1-4.
NOTE:One(1)Z-Wave®lightswitchcanbeassociatedtomultiple
controllers(uptove(5)controllersmaximum).
NOTE:Ifusinganon-LevitonProgrammer/Remote,refertothe
Programmer/RemoteinstructionsheetforassociatingaViziaRF+light
switch.
NOTE:YourLocalswitchwillbeassociatedbydefaulttobutton1.
Device Association:
Step 10
Excluding Load Control:
A) IfusingaLevitonZ-Wave®Programmer/Remote,Cat.No.VRCPG,
presstheMenubuttonandscrolldowntoSystemSetup.Pressthe
centerbuttontoselectSystemSetupMenu.ChooseAdvancedSettings.
PressthecenterbuttontoselectNetwork.Scrolldownto<Exclude
Node>andpressthecenterbutton.
B) IfusingVRCPGProgrammer/Remote,youwillbepromptedtoplace
LocalRelaySwitchintoprogrammingmode.
C) ToExclude,pressandholdbuttons2and4(refer to figure).Wait5
secondsuntiltheLEDturnsAmber.ReleasethebuttonsandtheLED
willblinkAmber.Youarenowreadytoexclude.
NOTE:IftheLEDontheLoadcontrolturnssolidRedwhileexcluding,
therehasbeenacommunicationerror.
D) WhilestandingclosetotheLoadcontroller(approximately1ft.),press
thecenterbuttonontheProgrammer/Remoteto<Exclude>devicefrom
thenetwork.
ARTWORK PRINT SPECIFICATIONS
FOLD SCHEME / BINDERY DIAGRAM
PART NUMBER REV DESCRIPTION
Line Screen:
Angle:
Resolution:
Offset Flexo
Other
Body Material:
Bindery
Thickness:
Trim
Perfect Bind
Die cut Saddle Stitch
Drill
Fold
The information in this document is the exclusive PROPRIETARY property of LEVITON MANUFACTURING COMPANY, INC. It is disclosed
with the understanding that acceptance or review by the recipient constitues an undertaking by the recipient. (1) to hold this information in strict
confidence, and (2) not to disclose, duplicate, copy, modify or use the information for any pupose other than that for which disclosed.
© 2009 Leviton Mfg. Co., Inc.
Unpublished, All Rights Reserved
PlantApprovals:
ARN: Pilot Rev:ECO Number:
Artwork Release Date:
Artwork Print Specification Sheet Rev A04.eps
PMCQA
Artist:
Notes:
Other
Cust Other
S & A
Mktg Eng
FOR LEVITON USE ONLY
SPECIFICATIONS :
PROCESS :
MANUAL INTERIORS / BINDERY / FOLD SCHEME :
COMMENTS :
For manuals - designates cover specifications
Dimensions:
Material:
Thickness:
Finish:
:
Spot
CMYK
1:
4:
3:
2:
Color(s):over
1:
4:
3:
2:
Fonts:
Spot
CMYK
1:
4:
3:
2:
Color(s):over
1:
4:
3:
2:
Fonts:
Fold LineDie Cut Punch/Drill Hole
Glue
Kiss Cut Cellophane
Fold Line
Perforate
Die Cut
Die Line Key:
DC

H anche
  
lac  Heletic a

nstruction sheet

Navigation menu